1 Ropani in Square Feet and Square Metres (Aana, Paisa, Daam)

Square land plot of 74 by 74 ft divided into 16 aana

1 ropani is equal to 5476 square feet, which is about 508.74 square metres. One ropani is divided into 16 aana, and each aana is 342.25 sq ft (about 31.80 m²).

The ropani system is used in Kathmandu Valley and the hill districts. Land in the Terai is measured in bigha, kattha and dhur instead. This post shows where the numbers come from, gives a ready table and explains how ropani compares with bigha and kattha.

How 1 ropani in square feet is worked out

The units in the ropani system go down by a factor of four each step below aana:

  • 1 ropani = 16 aana
  • 1 aana = 4 paisa
  • 1 paisa = 4 daam

A ropani is the area of a square 74 ft by 74 ft. So 74 × 74 = 5476 sq ft. Divide by 16 and you get 342.25 sq ft for one aana, which is a square 18.5 ft by 18.5 ft. To get square metres, multiply square feet by 0.09290304 (1 ft = 0.3048 m, and 0.3048 × 0.3048 = 0.09290304).

5476 × 0.09290304 = 508.737 m², which is usually rounded to 508.74 m².

P P P P 1 ropani = 16 aana 74 ft 74 ft 18.5 ft Ropani: 74 × 74 ft = 5476 sq ft Aana: 18.5 × 18.5 ft = 342.25 sq ft Paisa (P): 9.25 × 9.25 ft = 85.5625 sq ft Daam: 1/4 paisa = 21.39 sq ft Red square = 1 aana Dashed lines = 4 paisa
One ropani drawn to scale as a 74 ft square: 16 aana, and one aana split into 4 paisa.

Ropani, aana, paisa and daam table

UnitSquare feetSquare metres
1 ropani (16 aana)5476508.74
1 aana (4 paisa)342.2531.80
1 paisa (4 daam)85.567.95
1 daam21.391.99

Worked example

A lalpurja shows 4-8-2-0, which means 4 ropani, 8 aana, 2 paisa and 0 daam.

4 × 5476 = 21,904 sq ft. 8 × 342.25 = 2738 sq ft. 2 × 85.5625 = 171.13 sq ft. The total is 24,813.13 sq ft, or about 2305.21 m².

You can check any figure like this with the Jagga Napi land area converter. If you only have tape measurements of the plot sides, use the plot area calculator first.

How ropani relates to bigha, kattha and dhur

The Terai system uses 1 bigha = 20 kattha and 1 kattha = 20 dhur. In square feet:

  • 1 bigha = 72,900 sq ft (6772.63 m²)
  • 1 kattha = 3645 sq ft (338.63 m²)
  • 1 dhur = 182.25 sq ft (16.93 m²)

Comparing these with ropani gives:

  • 1 bigha = 72,900 ÷ 5476 = about 13.31 ropani
  • 1 ropani = 5476 ÷ 3645 = about 1.50 kattha
  • 1 kattha = 3645 ÷ 342.25 = about 10.65 aana
  • 1 aana = 342.25 ÷ 182.25 = about 1.88 dhur

Converting square metres from a survey map into ropani

Newer survey maps (naksa) and some lalpurja show area in square metres. To turn m² into ropani-aana-paisa-daam, first change it to square feet, then take out the largest unit at each step:

  1. Square feet = m² / 0.09290304.
  2. Ropani = how many whole 5,476 sq ft fit. Keep the remainder.
  3. Aana = how many whole 342.25 sq ft fit in the remainder.
  4. Paisa = how many whole 85.5625 sq ft fit in what is left.
  5. Daam = what is left / 21.390625 (this one can stay as a decimal).

Example: a plot of 250 m² on the map. 250 / 0.09290304 = 2,690.98 sq ft. That is less than one ropani, so 0 ropani. 2,690.98 / 342.25 gives 7 whole aana (2,395.75 sq ft), leaving 295.23 sq ft. That holds 3 paisa (256.69 sq ft), leaving 38.54 sq ft, which is 1.80 daam. So 250 m² = 0-7-3-1.80.

Example from tape measurements: a rectangular plot 40 ft by 55 ft = 2,200 sq ft = 204.39 m². 2,200 / 342.25 = 6 aana (2,053.5 sq ft), leaving 146.5 sq ft = 1 paisa (85.56) plus 60.94 sq ft = 2.85 daam. So the plot is 0-6-1-2.85, a little over 6 aana. Only use length x breadth when the corners are square; for any other shape use the plot area calculator.

Common plot sizes in aana

Most house plots in Kathmandu Valley are sold in aana. This table gives the area and one possible frontage and depth for each size. Real plots vary; the depth column just shows what a given frontage implies.

Plotsq ftm²Example frontage x depth (ft)
2 aana684.563.5920 x 34.2
2.5 aana855.679.4922 x 38.9
3 aana1,026.895.3925 x 41.1
4 aana1,369.0127.1830 x 45.6
5 aana1,711.3158.9835 x 48.9
6 aana2,053.5190.7835 x 58.7
8 aana2,738.0254.3745 x 60.8
10 aana3,422.5317.9650 x 68.5
1 ropani5,476.0508.7474 x 74

How much of a plot you can build on is set by your municipality's building bylaws (ground coverage, setbacks from the road and boundaries, floor area ratio). These differ between municipalities and change from time to time, so check the current bylaws at your ward or municipality office before you design. The naksa pass guide explains the approval steps.

Price per aana, per sq ft and per m²

Land is quoted per aana in the hills and Kathmandu Valley, but banks and valuers often work in square feet or square metres. With an example price of Rs 30 lakh per aana:

  • Per sq ft: 30,00,000 / 342.25 = Rs 8,765.52
  • Per m²: 8,765.52 / 0.09290304 = Rs 94,351.30
  • Per ropani: 30,00,000 x 16 = Rs 4.8 crore
  • For the 0-6-1-2.85 plot above: 2,200 x 8,765.52 = about Rs 1.93 crore

Rounding the plot to "6 aana" would price it at Rs 1.80 crore, Rs 12.8 lakh less. When money depends on it, always work from the full ropani-aana-paisa-daam figure or square feet, not a rounded aana count.

Road widening and usable area

If part of a plot falls inside a road right of way, the usable area can be less than the lalpurja area. Example: a 6 aana plot (2,053.5 sq ft) with a 30 ft frontage loses a 3 ft strip along the road. 3 x 30 = 90 sq ft, leaving 1,963.5 sq ft = 0-5-2-3.79. Ask the municipality about the road width before buying.

Dense brick and plastered houses on small plots in Kathmandu
Houses on small plots in Kathmandu (1987). Photo: Kathmandu Houses by Jan Kranendonk, CC BY-SA 4.0, via Wikimedia Commons

Common mistakes with ropani figures

  • Reading 4-8-2-0 as decimals. 4-8-2 is not 4.82 ropani. It is 4 ropani, 8 aana and 2 paisa, which is 4.53 ropani.
  • Treating paisa and daam as tiny. One paisa is 85.56 sq ft. At Rs 30 lakh per aana that is Rs 7.5 lakh.
  • Measuring along a slope. Tape lengths taken along sloping ground are longer than the plan lengths that the cadastral map uses, so the plot looks bigger than its official area.
  • Mixing up systems. 1 kattha (3,645 sq ft) is about 10.65 aana, not 1 aana. Check which system the lalpurja uses.
  • Trusting a broker's round figure. Compare the lalpurja, the survey map and your own measurement. If they differ, the Survey Office (napi) can re-measure.

Frequently asked questions

How many aana are in 1 ropani?

There are 16 aana in 1 ropani. Half a ropani is 8 aana, which is 2738 sq ft.

Is 1 ropani the same everywhere in Nepal?

Yes, the official value of 5476 sq ft is the same everywhere. What changes is the system: hill districts use ropani-aana and the Terai uses bigha-kattha. Always go by the figures on the lalpurja and the survey office map.

How many square metres is 1 aana?

1 aana is about 31.80 m². The exact figure is 342.25 × 0.09290304 = 31.796 m².

Preparing for the NEC licence or Lok Sewa?Practise 2,100+ civil engineering MCQs with answers, free.Start practising

Comments

Need a calculator we don’t have yet?

Tell us what you use on site or in class. The most requested tools get built next.